Filter by attributes Directions/Instructions <b>Use Instructions </b><br /> <ul> <li>Blockade areas to be stripped or finished. Floors will be very slippery until dry.</li> <li>Strip floors, using a Diversey stripper per the instructions on the stripper label</li> </ul> <b>Coating</b><br /> <ul> <li>Apply 3 or more medium coats using a clean finish mop or the Diversey ProSpeedTM/MC or TrailBlazerTM/MC Floor Finish Applicator System. Apply additional coats until desired gloss is obtained.</li> <li>Allow 30-45 minutes drying time between coats. Temperature, humidity and ventilation may affect drying time. Allow finish to cure for 24 hours before burnishing.</li> </ul> <b>Maintenance</b><br /> <ul> <li>Dust mop or sweep. Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to label directions.</li> <li>If desired, dry buff using medium to aggressive pad and 1000- 500 rpm equipment. Ultra-high speed burnish using a medium aggressiveness pad and 2000+ rpm equipment.</li> </ul> <b>Recoating </b><br /> <ul> <li>Dust mop or sweep Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to label directions</li> <li>Blockade area and apply 1-2 uniform coats of finish using a clean finish mop or the Diversey ProSpeedTM/MC or TrailBlazerTM/MC Floor Finish Applicator System. Allow finish to cure for 24 hours before burnishing.</li> </ul> <b>Removal</b><br /> <ul> <li>Remove using recommended Diversey brand stripper following label directions</li> </ul> <b>Precautions</b> <br /> <ul> <li>Do not dilute. Do not use on surfaces colder than 50°F (10°C) @ 15% RH. To avoid contamination, do not return unused finish to original container. Do not freeze.</li> </ul> <b>Use Instructions </b><br /> <ul> <li>Blockade areas to be stripped. Floors will become very slippery when stripper is applied. Exercise caution.</li> <li>Gloves, goggles and protective footwear is recommended when using this product</li> <li>Dilute or dispense using cold water</li> <li>Apply liberal amounts of stripper solution uniformly to floor with mop. Start at edges to provide more soak time. If splashing occurs, wipe off surfaces with a clean, damp rag.</li> <li>Let stripper solution soak 10-15 minutes. Mop agitate to loosen finish. Re-wet as necessary. Do not allow solution to dry on floor. Longer soak times may be necessary in cases of extreme buildup.</li> <li>Hand or machine scrub thoroughly using appropriate stripper pads or stripping brush. Pick up all solution with a clean mop, wet vac, or automatic scrubber. Mop up any 'tracks' left by wet vacs or scrubbers before they dry.</li> <li>Thoroughly rinse floor with clean water, using a mop and bucket. Let floor dry completely before applying a Diversey Green Seal®-Certified finish or other recommended Diversey brand floor finish or sealer.</li> </ul> <b>Use Instructions</b><br /> <ul> <li>Use appropriate personal protective equipment</li> </ul> <b>Dilute product as follows:</b><br /> <ul> <li><b>Light Build-up of Floor Finishes:</b> Dilute product between 1:8 (16 fl. oz. / gal.) and 1:10 (13 fl. oz. / gal.) with cool water</li> <li><b>Heavy Build-up of Floor Finishes:</b> Dilute product between 1:4 (32 fl. oz. / gal.) and 1:6 (24 fl. oz. / gal.) with cool water</li> <li><b>Heavy Build-up of Concrete Sealers:</b> Dilute product at 1:2 (64 fl. oz. / gal.) with cool water</li> <li>Blockade areas to be stripped. Floors will be very slippery when stripper is applied. Exercise caution.</li> <li>Apply liberal amounts of solution uniformly to floor with a mop. Start with the edges to give them more soak time. If splashing occurs, wipe off surfaces with a clean rag dampened with water.</li> <li>Let stripper solution soak for 10-15 minutes. Mop agitate to loosen finish or sealer. Re-wet as necessary, do not allow stripper to dry on the floor. Longer soak times may be necessary in cases of extreme buildup.</li> <li>Hand or machine scrub thoroughly using appropriate stripper pads or stripping brush</li> <li>Pick-up all of the solution with a clean mop, wet vac or automatic scrubber</li> <li>Mop up any "tracks" left by wet vacs or automatic scrubbers before they dry. Thoroughly rinse floor with clean water, using a mop and bucket.</li> <li>Let floor dry completely before applying recommended Diversey brand floor sealer or finish</li> </ul> <b>Important:</b><br /> <ul> <li>Do not use on wood, linoleum, rubber, marble, painted surfaces, on surface colored and acid dyed concrete floors as this product may harm these surfaces. Test for softening or color bleeding on asphalt floors before using.</li> </ul> <p><b>Directions for Use</b></p><p>Recommended for use on all types of resilient tile flooring and properly prepared hard surfaces.</p><p><b>RESTORATIVE MAINTENANCE: </b></p><p>Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco&#174; stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply finish in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 4 coats of finish is recommended. Note: This product is a self-sealing finish, however, if tile is old, worn or porous, initially applying 1 - 2 coats of a Betco sealer will enhance gloss and long term performance.</p><p><b>ROUTINE MAINTENANCE:</b></p><p>Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco&#174; One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating.</p><p><b>INTERIM MAINTENANCE:</b></p><p>Sweep large debris and dust mop. Top scrub the floor using Daily Scrub SC and maroon pad or equivalent to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above.</p><p>Please recycle empty containers. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum</p> <p><b>For Prespray Cleaning</b></p> <ul> <li>Thoroughly vacuum carpet and pre treat spots.</li> <li>Dilute 10 oz. Heavy Duty Prespray with 1 gallon hot water (1 L with 12 L) in pump-up sprayer or fill directly from J-Fill® dispenser.</li> <li>Spray carpet completely, paying particular attention to traffic lanes and spots.</li> <li>Agitate with a carpet rake, extractor brush, shampoo brush or bonnet.</li> <li>Allow 5-10 minutes for Heavy Duty Prespray to completely loosen soils.</li> <li>Thoroughly extract carpet with Extraction Rinse according to use directions. Use Liquid Defoamer in recovery tank if required.</li> </ul> <p><b>For Bonnet Cleaning</b></p> <ul> <li>Dilute at 1:32 or 4 oz./gal. (35 mL per L) with warm water.</li> <li>Apply light mist onto carpet bonnet.</li> <li>Bonnet buff carpet with your pad. Flip pad when soiled. When both sides are soiled, rinse or launder.</li> <li>e This solution can also be used for spot treatment. Treat spot, agitate and rinse thoroughly.</li> </ul> <p><b>For Use on Floors:</b></p> <ul> <li>Dilute ¼ cup Murphy Oil Soap in 1 gallon of warm water</li> <li>For heavy cleaning dilute ½ cup Murphy Oil Soap per gallon </li> <li>Clean with well wrung-out mop, and mop any excess water</li> <li>No rinsing required.</li> </ul> <b>Other Surfaces: </b> <p>Wet cloth with diluted Murphy Oil Soap liquid. Wipe clean to reveal wood's natural beauty</p> <p><b>Preparation</b></p><ul><li>Blockade areas to be stripped or finished. Floors will be very slippery until dry.</li><li>Before the first application of Mainstay® ProX Floor Finish, remove all old finish with any Diversey stripper.</li></ul><p><b>Coating</b></p><ul><li>Apply 3-4 medium coats of Mainstay® ProX Floor Finish with a clean finish mop. Let dry to the touch between coats (about 30 minutes).</li><li>On porous resilient or stone floors, seal first with 2 coats of the recommended Diversey sealer.</li></ul><p><b>Maintenance</b></p><ul><li>For daily cleaning dust mop or sweep.</li><li>Then wet clean with recommended Diversey cleaner in an autoscrubber or with a damp mop.</li></ul><p><b>Burnishing</b></p><ul><li>To renew gloss, spray buff as needed with recommended Diversey spray buff, a red or beige pad and a 175-1500 rpm machine. Or burnish with a UHS pad and a battery, cord electric or propane machine at 1500-2000+ rpm.</li></ul><p><b>Recoating</b></p><ul><li>Dust mop or sweep floor. Scrub floor with an autoscrubber or floor machine using a blue pad and the recommended Diversey cleaner at therecommended dilution. Rinse well and let dry.</li><li>Apply 1-2 new coats of Mainstay® ProX Floor Finish.</li></ul> <p><b>Pro-Tip:</b> Use for ordinary scrubbing of floor by hand or for automatic floor-scrubbing machines. Also used on walls, tables and all other hard surfaces.</p> <p><b>Usage Instructions</b></p><p>1. INSERT 2. SPRAY & CLEAN. 3. EJECT EMPTY BOTTLE & REPLACE. Do not remove cap. Place the arrow against the WetJet pole. Insert into WetJet device. Spray solution and mop. No need to rinse. Do not use on unfinished, oiled or waxed wooden boards, non-sealed tiles or carpeted floors because they may be water sensitive.</p> <p><strong>Preparation</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Blockade areas to be stripped or finished. Floors will be very slippery until dry.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Strip floors using a Diversey brand stripper per the instructions on the stripper label.</li></ul><p><strong>Coating</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Apply 3 or more medium coats of product using a clean finish mop or the Diversey ProSpeed TM/MC or TrailBlazer TM/MC Floor Finish Applicator Systems. Apply additional coats until desired gloss is obtained.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Allow 30-45 minutes drying time between coats. Temperature, humidity and ventilation may affect drying time. Allow finish to cure for 24 hours before burnishing.</li></ul><p><strong>Maintenance</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Dust mop or sweep.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to the label directions.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Burnish using appropriate pads.</li></ul><p><strong>Recoating</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Dust mop or sweep.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to label directions.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Blockade area and apply 1-2 uniform coats of finish using a clean mop.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Allow finish to cure for 24 hours before burnishing.</li></ul> <p>1. Clean area by sweeping or vacuuming.</p><p>2. Apply diluted concentrate with an automatic scrubber or power washing tool.</p><p>3. For best results, thoroughly mop and rinse floor with water as well as changing mopping solution frequently</p><p>No rinsing required except on rubber or asphalt tile. </p> <p>1. Insert. 2. Spray & clean. 3. Eject empty bottle & replace. Do not remove cap. Place the arrow against the WetJet pole. Insert into WetJet device. Spray solution and mop. No need to rinse. Refill: Gentle cleansers reveal wood's natural shine. Pre-mixed cleaning solution dissolves dirt and tough, sticky messes. Safe on all finished floors* (wood and laminate, marble, stone, ceramic tile, vinyl and linoleum). *Do not use on unfinished, oiled or waxed wooden boards, non-sealed tiles or carpeted floors because they may be water sensitive.</p> <p>Bona SuperCourt Cleaner Concentrate ratio is 1:128 (128 parts water to 1 part concentrate).</p><p>1. Remove the caps from the bottle and foil seals underneath each cap. </p><p>2. Replace both caps and tighten. </p><p>3. Grasp the bottle by the handle and tilt forward filling the concentrate into the reservoir. </p><p>4. Measure the amount of concentrate by using the one-ounce graduation marks on the front of the reservoir. </p><p>5. Remove the cap on top of the reservoir and pour the measured concentrate into the desired tank, bucket or bottle. </p><p>6. Fill the remaining tank, bucket or bottle volume with cold water. </p><p>7. Repeat as needed. Dispose of excess or unused products in accordance with local, state and federal requirements. </p> <p>Drop one PAC into a bucket filled with 1.6 gallons of warm water. After the satisfying fizz subsides, you're ready to mop. Simply mop all your hard surface floors as you normally would and enjoy the streak-free results. Not intended for use with spray mops. Keep out of the reach of children.</p> <p>For use as a top-scrub cleaner for wood floor coatings. ROUTINE MAINTENANCE: Dust mop floors daily. If using a treatment, use only a water-based treatment, being careful to follow label instructions. TACKING PROCEDURE: Dilute 1:4 gallon of water into a bucket. Soak several large towels in the solution, making sure they are thoroughly wet. Wring out the towels to remove excess moisture. Wrap a towel around a push broom and tack the floor. To prevent redeposit of dirt and oil, refold towel using clean sides as needed. Pay special attention to corners. Repeat the procedure in each area of the floor until the entire floor has been cleaned. Automatic Scrubber: Dilute 2 - 4 oz./gal. of water. No rinsing is required. INTERIM MAINTENANCE: Dilute 1:4 in a spray bottle for heavy spot cleaning. Spray and wipe dry. RESTORATIVE MAINTENANCE: Wet screening: Dilute product 2 - 4 oz./gal. of water. Use white or red floor pads. Use 175 RPM floor machine or automatic scrubber to wet screen the floor in preparation for new coating application. Rinse thoroughly removing all residue. See coatings labeled directions for proper procedures. Please recycle empty container.</p><p><br></p> <p>Read entire directions and warnings prior to use.</p><p>1. Sweep or vacuum area.</p><p>2. Apply diluted solution using automatic scrubber or mop and bucket.</p><p>3. For best results, change the mopping solution frequently.</p><p>No rinsing required except on rubber or asphalt tile. Rinse for best results on no-wax floors.</p><p>Always test in an inconspicuous area before use.</p><p>Prevention: Avoid breathing dust/fume/gas/mist/vapors/spray. Contaminated work clothing should not be allowed out of the workplace.</p><p>Wear protective gloves/ protective clothing/eye protection/face protection.</p> <p>Recommended for polished concrete and terrazzo surfaces for extended stain and etch protection. Clean entire area with Betco DensiClean, allow floor to dry prior to application. Apply Betco LiquiShield at proper application rate, 3,000 to 4,000 sq. ft. per gal, with a low-pressure sprayer spread with a microfiber applicator pad or mop and bucket application. Allow to dry to touch, 45 to 60 minutes, then apply second coat using the same procedures. Allow second coat to dry 60 minnutes then high speed burnish with Betco Si Burnish Pad. Allow 1 to 2 hours cure time before floor is exposed to full traffic. Allow 24 hours before the use of cleaners on the floor. Maintain floor with Betco Crete Rx DensiClean and Betco Crete Rx Cleaning Pads for maximum protection and shine. </p> <p>Recommended for use on all types of resilient tile flooring and properly prepared hard surfaces. </p><p><br /></p><p>RESTORATIVE MAINTENANCE: </p><p>Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco® stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply finish in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 4 coats of finish is recommended. Note: This product is a self-sealing finish, however, if tile is old, worn or porous, initially applying 1 - 2 coats of a Betco sealer will enhance gloss and long term performance. </p><p><br /></p><p>ROUTINE MAINTENANCE: </p><p>Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco® One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating. </p><p><br /></p><p>INTERIM MAINTENANCE: </p><p>Sweep large debris and dust mop. Top scrub the floor using Daily Scrub SC and maroon pad or equivalent to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above. </p><p><br /></p><p>Please recycle empty containers. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.</p> <p>Recommended for use on all types of resilient tile flooring and properly prepared hard surfaces.</p><p><b>RESTORATIVE MAINTENANCE:</b></p><p>Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply finish in uniform, medium to medium-heavy coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. 2 - 3 coats are recommended.</p><p>NOTE: This product contains an opaque application indicator that will clarify when drying. This is a self-sealing finish; however, if tile is old, worn or porous a Betco floor sealer can be used.</p><p><b>ROUTINE MAINTENANCE:</b></p><p>Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating.</p><p><b>INTERIM MAINTENANCE:</b></p><p>Sweep large debris and dust mop the floor. Top scrub the floor using Daily Scrub SC and maroon pad to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above.</p><p>Please recycle empty container. NOTE: Slip resistance meets or exceeds (ASTM D 2047-11) James Machine 0.5 minimum.</p> <p>Recommended for use on all types of stone flooring (brick, marble, slate, terrazzo and concrete-new and old), resilient tile, quarry and non-glazed ceramic tile.</p><p><br /></p><p>RESTORATIVE MAINTENANCE:</p><p>Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply finish in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 30 - 45 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 4 coats of finish is recommended.</p><p><br /></p><p>ROUTINE MAINTENANCE:</p><p>Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating.</p><p><br /></p><p>INTERIM MAINTENANCE:</p><p>Sweep large debris and dust mop. Top scrub the floor using Daily Scrub SC and maroon pad to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above. Please recycle empty containers.</p><p><br /></p><p>CONCRETE APPLICATION:</p><p>May be applied to new concrete after 30 days (fully cured) and a surface temperature above 50 °F. Prior to applying sealer to new concrete, use an acidic solution to neutralize excess alkalinity. All new concrete must be cleaned and rinsed. Not for use outdoors. Old concrete must be cleaned with a degreasing solution and rinsed for proper adhesion.</p><p><br /></p><p>GLAZED TILE/POLISHED SURFACES:</p><p>1. Test in an inconspicuous area first, proper adhesion may be difficult due to lack of porosity.</p><p><br /></p><p>Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.</p> <p>Recommended for use with steam and hot water extractors on all types of carpeting (including Stain Resistant), upholstery and rugs. Please recycle empty containers.</p><p>1. Vacuum carpet.</p><p>2. Dilute 0.5 oz./gal. or 3.9 mL/L (1:256) of water. If carpet is heavily soiled, 1 oz./gal. or 7.8 mL/L (1:128) of water. Cleaning solution may also be used as a prespray, sprayed directly onto the carpeting.</p><p>3. Follow operating instructions on extraction equipment.</p><p>4. Allow the carpet to dry thoroughly before allowing traffic.</p> <p>Remove soil and dust mop the floor. Spray a light mist of product on the floor in front of the floor machine. DO NOT OVERWET. Using a nylon or polyester spray buff pad, buff the floor where the fine mist of spray buff has been applied. Flip or change pad as necessary. After spray buffing the floor is completed, dust mop the floor if dust is still present.<br />NOTE: In order for spray buff to work correctly, three or four base coats of floor finish must be applied before using spray buff in order to achieve maximum gloss and wear properties. Heavy traffic areas may require dust mopping, followed by damp mopping, followed by spray buffing. Use of this spray buff will eliminate powdering and will never yellow the floor.<br />NOTE: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.</p> <ul> <li>A highly effective cleaner designed to remove soils and oils without dulling or altering the appearance of your floor</li> <li>Designed for use on most floor types</li> <li>Part of a comprehensive floor care offering for cleaning, maintaining, stripping and finishing floors</li> </ul> <ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Blockade areas to be stripped or finished. Floors will be very slippery until dry.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Strip floors, using a Diversey stripper per the instructions on the stripper label.</li></ul><p><strong>Coating</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Apply 3 or more medium coats using a clean finish mop or the Diversey ProSpeedTM/MC or TrailBlazerTM/MC Floor Finish Applicator System. Apply additional coats until desired gloss is obtained.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Allow 30-45 minutes drying time between coats. Temperature, humidity and ventilation may affect drying time. Allow finish to cure for 24 hours before burnishing.</li></ul><p><strong>Maintenance</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Dust mop or sweep. Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to label directions.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>If desired, dry buff using medium to aggressive pad and 1000- 500 rpm equipment. Ultra-high speed burnish using a medium aggressiveness pad and 2000+ rpm equipment.</li></ul><p><strong>Recoating</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Dust mop or sweep.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to label directions.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Blockade area and apply 1-2 uniform coats of finish using a clean finish mop or the Diversey ProSpeedTM/MC or TrailBlazerTM/MC Floor Finish Applicator System. Allow finish to cure for 24 hours before burnishing.</li></ul><p><strong>Removal</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Remove using recommended Diversey brand stripper following label directions.</li></ul><p><strong>Precautions</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Do not dilute. Do not use on surfaces colder than 50°F (10°C) @ 15% RH. To avoid contamination, do not return unused finish to original container. Do not freeze.</li></ul> <ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Blockade areas to be stripped or finished. Position wet-floor signs around area to be cleaned.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Strip floor using recommended Diversey brand stripper according to label directions</li></ul><p><strong>Coating</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Apply 2-3 uniform coats using a clean finish mop or the TrailBlazerTM/MC Floor Finish Applicator System. Apply additional coats until desired gloss is obtained.</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Allow 30 minutes drying time between coats. Temperature, humidity and ventilation may affect drying time. Allow finish to cure for 24 hours before buffing.</li></ul><p><strong>Maintenance</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Dust mop or sweep</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner following label directions</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>If desired, spray buff using recommended Diversey brand floor maintainer to enhance gloss</li></ul><p><strong>Recoating</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Dust mop or sweep</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Deep scrub floor using Diversey cleaner according to label directions</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Blockade area and apply 1-2 uniform coats of finish using a clean finish mop or the Diversey TrailBlazerTM/MC Floor Finish Applicator System. Allow finish to cure for 24 hours before buffing.</li></ul><p><strong>Removal</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Remove using recommended Diversey brand stripper according to label directions</li></ul><p><strong>Best Results</strong></p><ul><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Do not dilute</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>Do not use on surfaces colder than 50°F (10°C) @ 15% RH</li><li data-list="bullet"><span class="ql-ui" contenteditable="false"></span>To avoid contamination, do not return unused product to original container</li></ul><p>Note: Floors will be slippery when wet or contaminated with foreign materials. Promptly clean-up spills and foreign materials. Meets ASTM D2047 requirements for slip resistance.</p><p><br></p> <ul><li> For use as a powerful rinse aid</li><li> Safe to use on all colorfast carpets</li></ul> <ul><li> For use as daily floor cleaner and general cleaner.</li><li> Use as spray and wipe application or in mop and bucket.</li><li> Use in autoscrubber.</li></ul><p><br /></p> <ul><li> Recommended ESIor removing water-based acrylic floor finishes from all types of resilient tile and hard surfaces. Pre-test in a small area; color bleeding or discoloration may occur on linoleum, rubber tile or asphalt tile.</li><li> Not recommended for stripping linoleum or sheet vinyl floors.</li><li> Sweep or dust mop the floor to remove any large debris. Dilute with warm to hot water.</li><li> For normal stripping, dilute 13 oz./gal. or 100 mL/L (1:10) of water.</li><li> For heavy stripping, dilute 25 oz./gal. or 200 mL/L (1:5) of water.</li><li> Apply solution liberally to floor surface. Allow a minimum of 5 minutes contact time. Be sure to keep surface wet at all times. Agitate with a low-speed rotary machine, automatic scrubber or stripping machine. Pick up the solution with a wet vacuum, an automatic scrubber or a mop and bucket and thoroughly rinse the floor. Allow floor to dry completely before applying finish or sealer. No flood rinsing is necessary if surface appears free of dust and residue. Please recycle empty container.</li></ul> <ul><li> Responds beautifully to conventional, high-speed or UHS equipment and maintenance procedures</li><li> May require a sealer on highly polished stone, glazed clay tile, and some rubber floors</li><li> Not intended for use on cork, wood, or bamboo flooring unless specified by the manufacturer</li></ul> <ul><li> Use as a daily floor cleaner on most floor types</li><li> Can also be used as a high performance general purpose cleaner</li></ul> <ul><li> Dust mop or sweep</li><li> Dilute, dose or dispense product into spray bottle, mop bucket or autoscrubber using cold water</li></ul><p><b>Mop and Bucket Floor Cleaning</b></p><ul><li> Mop floors; no rinsing is necessary</li><li> Pick up excess cleaner with lightly wrung-out mop</li></ul><p><b>Automatic Scrubber Floor Cleaning</b></p><ul><li> Scrub with red pad daily</li><li> Double-scrub with green/blue pad before recoating or restoring. Trail mop machine turns, edges and low spots to pick-up cleaning solution</li></ul><p><b>Left behind by machine</b></p><p> Floors will be slippery when wet</p><p><b>Spray and Wipe Cleaning</b></p><ul><li> Spray, wipe and allow surface to dry</li></ul> <ul><li> For best results, always vacuum carpet first.</li><li> Fill extractor solution tank with Extraction Rinse SC solution from dispenser.</li><li> Light duty: As needed, pre-spot with the appropriate spotter. Extract following equipment maker's operating instructions.</li><li> Medium to Heavy Duty: As needed, pre-spot with the appropriate spotter. Fill pressure sprayer with Soil Release/Bonnet Buff solution on traffic lanes and soiled areas of carpet and allow to dwell for a few minutes.</li><li> Before solution dries, extract carpet in normal manner.</li></ul><p>Note: If being used for the first time, test for colorfastness in an inconspicuous area before use.</p> <ul><li>Apply Heavy Duty Prespray according to use directions, depending on soil level.</li><li>For synthetic carpets, dilute 1 oz. Extraction Rinse with 1 gal. luke warm water (30 mL per 3.8 L) in extractor. Dilute 1 oz. with 5 gal.(30 mL per 19 L) water for wool carpets (use cool water).</li><li>Thoroughly extract carpet.</li><li>Groom carpet with clean carpet rake or stiff synthetic broom and allow to air dry.</li></ul><p>Note: If being used for the first time, test for colorfastness in an inconspicuous area before use.</p> <ul><li>Blockade areas to be stripped or finished. Floors will be very slippery until dry.</li><li>Strip floor using a Diversey stripper per the instructions on the stripper label.</li></ul><p><b>Coating</b></p><ul><li>Apply 1 to 2 coats of Over & Under® ProX floor sealer using a clean mop.</li><li>Allow 30 minutes drying time between coats. Temperature, humidity and ventilation may aect drying time. Allow finish to cure for 24 hours before burnishing.</li><li>Apply 1 or more coats of recommended floor finish according to label directions.</li></ul><p><b>Burnishing</b></p><ul><li>Dust mop or sweep floor.</li><li>Clean the floor with mop or automatic scrubber using the recommended cleaner according to label directions.</li><li>Maintain the finish gloss using periodic recoating, spraybung or burnishing according to finish label.</li></ul><p><b>Removal</b></p><ul><li>Remove using recommended stripper according to label directions.</li></ul><p><b>For Best Results</b></p><ul><li>Do not dilute.</li><li>Do not use on surfaces colder than 50 degrees F/10 degrees C.</li><li>To avoid contamination, do not return unused product to original container.</li></ul><p><b>Note</b>: Floors will be slippery when wet or contaminated with foreign materials. Promptly clean up spills and foreign materials. Not intended for use in outdoor areas. Meets ASTM D-2047 requirement for slip resistance.</p> <ul><li>Dust mop or sweep floor.</li><li>Dilute, dose or dispense product into spray bottle, mop bucket or autoscrubber using cold water.</li></ul><p><b>Mop and Bucket Floor Cleaning</b></p><ul><li>Mop floors; no rinsing is necessary.</li><li>Pick up excess cleaner with lightly wrung-out mop</li></ul><p><b>Automatic Scrubber Floor Cleaning </b></p><ul><li> Scrub with red pad daily. </li><li>Double-scrub with green/blue pad before recoating or restoring. Trail mop machine turns, edges and low spots to pick-up cleaning solution left behind by machine. </li><li>Floors will be slippery when wet. </li></ul><p><b>Spray and Wipe Cleaning </b></p><ul><li>Spray, wipe and allow surface to dry.</li></ul> <ul><li>Use as floor conditioning and neutralizing before applying finish.</li><li>Effective at counteracting urine odors on hard floors, grout and carpeting</li><li>Suitable for use in non-food processing areas</li></ul><p><br /></p> Recommended for mopping or autoscrubbing finished floors. Can also be used as a spray and wipe cleaner on appliances, desks, plastic, stainless steel and painted surfaces. <br /> <ul> <li>Dilute 0.5 US oz./US gal. or 4 mL /L of water, depending on soil conditions.</li> <li>Apply cleaning solution using a mop or autoscrubber.</li> <li>Pick up the solution. Rinsing is not required except in very dirty situations .</li> <li>Allow floor to dry thoroughly.</li> </ul> Recommended for use on all types of resilient tile flooring and properly prepared hard surfaces. This product is of specific benefit in preparing old, worn or porous tile floors for finishing. <br /><br />RESTORATIVE MAINTENANCE:<br />Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco® stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply sealer in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 2 coats of sealer is recommended. This sealer can be used as a finish coat, however, for a better shine, increased protection and easier maintenance, we recommended the application of 2 - 4 coats of a Betco floor finish that best fits your maintenance program. <br /><br />Please recycle empty containers. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.
Floor & Carpet Cleaners Sort by Display Order Price: High to Low Price: Low to High Name: A to Z Name: Z to A Created on
Display 6 12 18 per page
CDC3320000514
Aerosol - 15 fl oz (0.5 quart) - Fresh Clean Scent - 8 / Carton - White
BET4200400
Liquid - 128 fl oz (4 quart) - 1 Each - Clear
DVO101109753
For Floor, Hard Surface - Concentrate - Liquid - 128 fl oz (4 quart) - Citrus Scent - pH Neutral, Non Alkaline, Film-free, Easy to Use, Low Foaming, Kosher, Versatile, Rinse-free - Orange Bottle - 4 / Carton
GJO44040
For Floor - Concentrate - 128 fl oz (4 quart) - White - 4 / Carton
BET8880400
Ready-To-Use Liquid - 128 fl oz (4 quart) - 128 oz (8 lb) - 4 Pack - Clear
BET154B500
Concentrate - 640 fl oz (20 quart) - 1 Each - Low Foaming, Rinse-free, Fast Acting, Versatile, Pleasant Scent, Residue-free - Clear, Amber
BET605B500
640 fl oz (20 quart) - Mild Scent - 1 Each - Durable, Slip Resistant, Gloss Resistant, Black Mark Resistant, Detergent Resistant - White
MLB12340012
For Floor - Spray - 32 fl oz (1 quart) - Durable, Slip Resistant - White - 12 / Carton
PGC77811CT
For Multi Surface, Multipurpose - Liquid - 42.2 fl oz (1.3 quart) - Lavender Vanilla Scent - Non-streaking, Phosphate-free, Quick Drying - Purple - 4 / Carton
PGC77809CT
For Multi Surface - Liquid - 40.6 fl oz (1.3 quart) - Gain Scent - Recommended For: Dirt Remover, Grime Remover - Quick Drying, Absorbent - Green - 4 / Carton
PGC77133CT
For Multi Surface - 40.6 fl oz (1.3 quart) - Recommended For: Bacteria Remover, Dirt Remover, Grime Remover - Quick Drying - Purple - 4 / Carton
DVO101110007
For Floor - Ready-To-Use - 84.5 fl oz (2.6 quart) - Recommended For: Black Mark Remover - Low Odor, Durable, Quick Drying, Non-yellowing - White - 1 Each
ZPEZUHTFF128
Liquid - 128 fl oz (4 quart) - 1 Each - Clear, Green
MLB18050065T
For Floor, Tile, Rubber, Marble Floor, Stone Floor - Neutral Scent - White - 4 / Carton
ZPEZUFSLR128
Liquid - 128 fl oz (4 quart) - 1 Each - Blue
MLB26040069
For Floor, Kitchen, Mortar - 2.60 oz (0.16 lb) - Dirt Resistant, Heavy Duty, pH Neutral, Slip Resistant - White - 30 / Carton
SMP11201
Concentrate Liquid - 128 fl oz (4 quart) - 1 Each - Sand
DVO94996440
Concentrate - 32 fl oz (1 quart) - Citrus Scent - 6 - Heavy Duty, Film-free, Rinse-free, pH Neutral, Dilutable - Yellow
/* Added for Digitol */ /* End Added for Digitol */
